Course catalogue

Presentation

This training course describes the various components of a shaft line and the different types of shafts and their couplings, the importance of shaft alignment and the various methods utilized for shaft alignment. The course provides also a brief introduction to the vibrations that may affect the shaft lines.

Objectives

On completion of the training, students will be able to:

Get familiar and understand the components of a shaft line, know the types of shafts and their couplings, understand the protection required and the shaft line components scantlings and get familiar with the required tests and certification of shaft lines.

Understand the importance of shaft alignment and the factors influencing the alignment, know the different alignment methods currently employed and understand the shaft alignment issues for installations other than the main shafting line.

Understand the different types of vibrations that may affect shaft systems, know the general principles of torsional and axial vibrations and get familiar with the vibration control methods and vibration tests and measurements

Program

Module 1 - Shaft Lines and Propeller

Shaft line components: Shafts, shaft liners, propellers, propeller cap, shaft and intermediate bearings, stern tube, stern tube bushes and seals

Couplings: Flanged couplings, hydraulic couplings, flexible couplings

Design and construction: Propeller shaft key and keyway, shaft materials, couplings materials, coupling bolts, shaft scantlings, shaft monitoring

Inspection and certification: Inspections during construction, material tests, hydrostatic tests, certification, sea trials

Module 2 – Shaft Alignment

Introduction

Alignment calculation

Required information

Factors influencing the alignment: Draught, buoyancy, rigidity of the bearing base, temperature

Alignment methods: Gap and sag method, sighting method, jack-up method, strain gauge method

Alignment verification on board

Shafts for other installations: Alignment techniques, preparation, types of misalignment, alignment methods

Module 3 – Shaft Vibrations

Torsional vibrations

Rules requirements

Vibration damper

Barred speed range

Required documentation

Calculation principles

Axial vibrations

Vibration control and tests

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Shaft Alignment, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Shaft Alignment is obtained after completing the course and passing the online test.

Presentation

This training course provides a general overview of the requirements of the International Load Lines Convention and the conditions of assignment of load lines.

Objectives

On completion of the training, students will be able to:

Know the general requirements of the International Load Lines Convention and understand the conditions of assignment of load lines.

Know the different types of surveys; understand the scope of each survey and the certificates, records and documents associated with the Load Lines Convention.

Know the most common deficiencies and PSC detainable items in connection with the Load Lines Convention.

Program

History of Load Lines Convention

Purpose of the Convention

Definitions

Freeboard calculation

Load line marks

Conditions of assignment

o Information to be supplied to the Master

o Doors

o Cargo and other hatchways

o Machinery space openings and miscellaneous openings

o Ventilators and air pipes

o Scuppers, inlets and discharges

o Scuttles and windows

o Freeing ports

o Protection of crew

o Special conditions of assignment for Type A ships

Special requirements for ships assigned with timber freeboards

Certificates, records and other documents

Scope of Load Line surveys

o Initial survey

o Annual survey

o Renewal survey

Common PSC deficiencies related to Load Lines

o PSC statistics

o Detainable deficiencies

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Load Lines, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Load Lines is obtained after completion of the course and passing the online test.

Presentation

This training course provides a general overview of the MARPOL requirements concerning the protection against oil pollution from cargo spaces of oil tankers.

Objectives

On completion of the training, students will be able to:

Understand the MARPOL requirements for the prevention of oil pollution from cargo spaces of oil tankers.

Get familiar with the pollution prevention equipment required by the MARPOL Convention.

Know the requirements for survey and certification of oil tankers.

Program

Segregated ballast tanks

Double hull and double bottom

Pump-room bottom protection

Subdivision and stability

Slop tanks

Pumping, piping and discharge arrangements

Oil discharge monitoring and control system

Oil/water interface detector

Crude oil washing system

Control of discharge of oil

Oil record book part II

Ship-to-ship transfer

Survey and certification, type-approval certificates

Different survey types

Certificate

On completion of the training program, the student will be awarded:

A Certificate of MARPOL Oil Pollution from Cargo Spaces, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of MARPOL Oil Pollution from Cargo Spaces is obtained after completion of the course and passing the online test.

Presentation

This training course provides an overview of the Magnetic Particles Testing (MT) method for non-destructive examination of materials and welding, its objectives and principles.

Objectives

On completion of the training, students will be able to:

Understand the basic physical principles of magnetic particle testing.

Know the testing procedure and the inspection process referred to testing materials and equipment.

Differentiate applications and the acceptance criteria applied.

Get familiar with the purpose of reference materials and/or blocks to ensure the quality of test performance and testing results.

Program

Basic principle

Testing procedure

o Surface preparation

o Magnetization

o Applying detection media

o Inspection and recording

o De-magnetization

o Post-cleaning

Testing materials and equipment

o Detection media–dry and wet magnetic particles

o Equipment for magnetization

o AC/DC

Applications and acceptance criteria

o Scope

o Indications

o Acceptance criteria

o Test report

Reliability, quality of test performance

o Verification of magnetization

o Viewing conditions

o Detection media

o Magnetic flux indicators

o NDT personnel competence

Certificate

On completion of the training program, the student will be awarded:

A Certificate of NDT – Magnetic Particles Testing, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of NDT – Magnetic Particles Testing is obtained after completion of the course and passing the online test.

This course includes all subjects needed to prepare candidates for the rotary drilling well control exam, surface and subsea BOP stack on driller level (Level 3).

This course includes all subjects needed to prepare candidates for the rotary drilling well control exam, surface and subsea BOP stack at supervisor level (Level 4).

A printed course manual and exercise book is provided for all attendees. The IWCF exam is included in the course.

The course has been made on basis of the recommendations for enhancements to well control training, issued by the International Association of Oil & Gas Producers (OGP).

Course Content

- Kick prevention

- Shut in procedures

- Well control methods

- Kill sheet calculations

- Practical simulator training

- Circulation methods

- Practical simulator assessment

- IWCF written exam on the last day (Friday)

Please note! The course is in Norwegian, however you have the option to select the exam language to be English

Provided in association with Astutis, approved centre 1857.

IOSH Managing Occupational Health and Wellbeing course will provide managers with the practical advice and tools to help create a healthy and productive workplace.

IOSH Managing Occupational Health and Wellbeing is targeted at line managers and offers them practical advice to manage health risks and understand their responsibilities for the health and wellbeing of staff.  It equips line managers with the basic tools and techniques to play their part in improving health and wellbeing across their organisation.

The course is split into 4 modules and covers:

• Importance of managing workplace health and wellbeing

• Health risk management

• Fitness for work and the need to manage changes in the health status of employees

• The business value of promoting a wellbeing programme

Presentation

This training course provides an overview of the different techniques employed for non-destructive tests (NDT) of materials and welding, their objectives and principles.

Objectives

On completion of the training, students will be able to:

Know the objectives and principles of the various non-destructive testing methods.

Differentiate NDT methods regarding application selection and physical principles.

Understand the evaluation process referred to the testing procedure.

Be familiar with the reliability of the various NDT methods.

Program

Definitions and terminology

Role of non-destructive testing

NDT methods

Systematisation of NDT methods

o Visual testing

o Penetrant testing

o Magnetic particles testing

o Radiographic testing

o Ultrasonic testing

Evaluation of NDT findings

Indications and flaws

Acceptance criteria

Reliability of NDT

Probability of detection

NDT operators certification

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Introduction to NDT, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Introduction to NDT is obtained after completion of the course and passing the online test.

The course is in accordance with NS-EN 1591-4 and undergoes the same course content as an ordinary four-day course but without the use of hydraulic torque tool and tensioning tools.

The use of a mechanical torque wrench is the main focus but also a review of procedures, flanges, gaskets, practical tasks and more.

The course ends with a theoretical and practical exam. If passed, the approval is valid for 5 years.

Courses are conducted in Stavanger or Bergen
and is carried out on request.

Course price NOK 5300, - pr. participant.

Hensikt: Grunnleggende overlevelsestrening for offshore vindindustri. 

Ved gjennomføring av Global Wind Organization (GWO) Basic Safety Training (BST) vil delegatene ha en bevissthet om farene som oppstår når de arbeider i vind-industrien og hvordan man kontrollerer og reduserer disse farene.

Kursdeltakerne vil få (repetert) kunnskap og ferdigheter til å anerkjenne fordeler og begrensninger knyttet til livreddende utstyr og PVU samt korrekt bruk av dette i forbindelse med offshore vind. 

Hensikten med kurset er å gi deltakerne kunnskaper/oppfriskning om livreddende utstyr, GMDSS og SAR utstyr, hvordan en kollektivt kan øke sjansen til overlevelse i en nødsituasjon, hvordan entre og forlate vindturbiner, samt evakuering i nødsituasjoner. 

Kurset dekker krav til opplæring av personell og repetisjonskurs både land- og havvind iht:

- Global Wind Organization (GWO)

- Arbeidstilsynet (Forskrifter)


Kompetanse for «Sea Survival» skal vedlikeholdes iht. retningslinje i GWO standarden. Det skal gjennomføres repetisjonskurs hvert 2. år.

This course is only available in Norwegian.

Objective: The purpose of the training is to provide users of work equipment mentioned in § 10-1 and 10-3 in «Regulations on the performance of work» (no. 1357), a good general basic training in the safe use of work equipment, so that accidents and accidents in connection with use is avoided.

The authorities set requirements for basic safety certification of persons who are to drive forklifts, mass transfer machines and cranes. The requirements include both theoretical and practical training. To complete the common theory, one must take and pass a theoretical exam.

Module 1.1 Working environment, responsibilities and consequences are common to machine, forklift and crane. If you can document that you have module 1.1 from before that is not older than 3 years, you can start right on module 2.3.

Content:

- Laws and regulations
- Working environment, responsibilities, and consequences
- Environmental
- Safety regulations
- Dangerous goods, marking and handling

Objective: The aim of the training is that those who are given training are given the opportunity to acquire theoretical and practical knowledge about fall protection and the correct use of rescue equipment, rescue of free-hanging persons, rescue of personnel over open sea, tank, stretcher transport, descent and treatment of personnel after fall accident.

The training is adapted for personnel who are part of fall protection / rescue teams on board an installation, but also for personnel who want a basic understanding of a rescue operation, evacuation equipment after a fall accident when using fall protection / rescue equipment.

The course runs over 3 days (24 hours)

Repetition 2 every year in accordance with NOG 113 and SFS.

Content:

- Introduction
- Regulations, guidelines
- Best practice
- Risk assessment
- Fall protection equipment
- Use of personal protective equipment
- Knowledge of different equipment and methods
- The equipment's limitations and possibilities
- Requirements for maintenance, storage and control
- Consequences of falls

Practical and theoretical review of rescue exercises

- Planning and risk assessment of rescue
- Basic first aid
- Rescue operation w / fresh air equipment
- Rescue of a hanging person
- Rescue from tanks / cramped spaces
- Rescue over open sea
- Descent / hoisting of person
- Stabilization of person
- Knowledge of hanging trauma

The Norwegian authorities require that employees who use lifts (personnel lifts) must be able to document practical and theoretical training in their use. The employer is responsible for ensuring that employees receive the necessary training. (“Regulations regarding the execution of work” no. 1357, section 10-2 Requirements regarding documented safety training in the use of work equipment.) The course provides a basic theoretical and practical introduction to the safe use of lifts (personnel lifts). A certificate of competence is issued to participants in order to fulfil the legislation’s documentation requirements.
Objective: To provide course participants with increased knowledge and awareness of safety measures in order to avoid injuries and accidents at the workplace. 

The following topics are covered:
– Assembly
– Operation
– User qualities
– Areas of use
– Maintenance and control
– Safe use and servicing
– Classes A, B and C
– Accidents
– Legislation and regulations

Hensikt:

Målsetting med opplæring er at den som gis opplæring tilegner seg tilstrekkelig kunnskap om metoder for å lede og veilede løfteoperasjoner slik at de blir forskriftmessig utført.

Opplæringen gir også kunnskap om farer forbundet med løfteoperasjoner samt bruk av risikokartlegging.

Kurset gir deltakere kunnskap til å kunne utøve overordnet operasjonell ledelse av løfteoperasjoner. Med det menes å kunne planlegge, risikokartlegge og evaluere, samt forebygge ulykker. Videre vil deltaker også tilegne seg kunnskaper om å gjøre rede for materialhåndteringsplan, oppbevaring og bruk av utstyr.

Målsetting med opplæring er at den som gis opplæring tilegner seg tilstrekkelig kunnskap om metoder for å lede og veilede løfteoperasjoner slik at de blir forskriftmessig utført.

Innhold:

• Krav og ansvar til rollen operasjonelt ansvarlig

• Lover, forskrifter, standarder og retningslinjer som gjelder vedr. bruk av løfteutstyr

• Overordnet operasjonell ledelse av løfteoperasjoner

• Helhetlig planlegging av løfteoperasjoner

• Risikokartlegging

• Identifisering av og etablering av barrierer. Gjennomføring og evaluering av en løfteoperasjon

• Informasjonsutveksling

• Krav for oppbevaring av løst løfteutstyr

• Krav for ulike typer løfteutstyr

• Krav til fadder, praksis og sensor

• Avsluttende prøve

This course is made for personell envolved in design, planning, projecting, installation and maintenance on electrical installations and equipment offshore. 

The purpose of the standard is to minimize the hazards to people and equipment, whilst optimizing dependability.

Objective: The purpose of the standard is to minimize the hazards to people and equipment, whilst optimizing dependability.

Content:

- An easy to understand overview and explanation of the committees/regulations/standards and how they are intertwined. 

- Presentation of the regulations and norms: PTIL 5 HMS, Nek 410 (IEC 60092), Nek 420 (IEC 60079), ATEX directives including standards and the Norsok series. 

- The structure and history of the IEC 61892 series, and the scope and application. 

- By using a fictive, illustrated installation, we will focus on the practical elements covered in the following standards: 

o IEC 61892-1 - General requirements and conditions 

o IEC 61892-2 - System Design 

o IEC 61892-3 – Equipment 

o IEC 61892-4 – Cables 

o IEC 61892-6 – Installation 

o IEC 61892-7 – Hazardous areas

This course is only available in Norwegian.

Provided in association with Astutis, NEBOSH Learning Partner 807.

The NEBOSH National Diploma in Occupational Health and Safety is an advanced health and safety qualification. Equivalent to an undergraduate degree in OHS. The NEBOSH Diploma is NEBOSH's flagship qualification. It is recognized by employers and professional bodies in over 180 countries around the world!

The qualification will develop competence in all areas of health and safety so you can reduce risk in dangerous environments and keep people safe. It is the ideal course if you want a successful, long-term career in health and safety.

Unit A: Managing Health and Safety

This unit provides an in-depth understanding of the key areas for managing health and safety, covering moral, economic, and societal drivers, health & safety law, and health & safety management systems. 

A1 - Principles of health & safety management

A2 - Principles of health & safety law

A3 - Criminal Law

A4 - Civil Law

A5 - Loss causation and incident investigation

A6 - Measuring and reviewing health and safety           

A7 - Identifying hazards, assessing and evaluating risk

A8 - Risk control

A9 - Organisational factors

A10 - Human factors

A11 - The role of health & safety practitioner

Unit B: Hazardous Agents in the Workplace

Unit B details all major aspects of managing chemical, biological, physical and physiological hazards in the workplace.

B1 - Managing Occupational Health

B2 - Identification, assessment & evaluation of hazardous substances

B3 - Control of hazardous substances

B4 - Monitoring and measuring

B5 - Biological agents

B6 - Physical agents - noise and vibration

B7 - Physical agents - radiation

B8 - Mental ill-health & dealing with violence & aggression at work

B9 - Musculoskeletal risks and controls

B10 - Work environment risks and controls

Unit C: Workplace and Work Equipment Safety

Unit C provides a thorough understanding of how to create and manage safe working environments, covering welfare, fire, dangerous substances, work equipment, electricity, construction, and transport. 

C1 - Workplace welfare requirements and specific workplace issues

C2 - Fire and explosion

C3 - Workplace fire risk assessment

C4 - Storage, handling, and processing of dangerous substances

C5 - Work equipment (general)

C6 - Work equipment (workplace machinery)

C7 - Mobile, lifting, access, and work at height equipment

C8 - Electrical safety 

C9 - Construction & works of a temporary nature - hazards and controls

C10 - Workplace transport and driving for work

Presentation

This training course provides an overview of the Penetrant Testing (PT) method for non-destructive examination of materials and welding, its objectives and principles.

Objectives

On completion of the training, students will be able to:

Understand the basic physical principles of liquid penetrant testing.

Know the testing procedure and the inspection process referred to testing materials and equipment.

Differentiate applications and the acceptance criteria applied.

Get familiar with the purposes of reference materials and/or blocks to ensure the quality of test performance and testing results.Program

Basic principle, capillary effect

Physical properties of the penetrant

Testing procedure

o Pre-cleaning

o Penetrant application

o Excess penetrant removal

o Developer application

o Inspection and recording

o Post-cleaning

Testing materials and equipment

o Penetrants

o Removal methods

o Developers

o Equipment

Applications and acceptance criteria

o Indications

o Test report

Reliability, quality of test performance

o Surface preparation and condition

o Types of penetrant materials and equipment used

o Penetrations and development time

o Viewing conditions

o The temperature of the test surface

o The material tested and flaws expected

o NDT personnel competence

o Safety issues

Certificate

On completion of the training program, the student will be awarded:

A Certificate of NDT – Penetrant Testing, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of NDT – Penetrant Testing is obtained after completion of the course and passing the online test.

Presentation

This training course provides an overview of the Ultrasonic Testing (UT) method for non-destructive examination of materials and welding, its objectives and principles.

Objectives

On completion of the training, students will be able to:

Understand the basic physical principles of ultrasonic testing.

Know the testing procedure and the inspection process referred to the equipment used.

Differentiate applications and the acceptance criteria applied.

Get familiar with the purpose of calibration and reference blocks to ensure the quality of test performance and test results.

Program

Basic principle

o Ultrasonic waves and propagation

o Ultrasonic pulse-echo principle

Equipment and testing materials

o Ultrasonic testing instruments

o Ultrasonic testing probes

o Coupling media

o Calibration and reference blocks

Testing procedure

o Surface preparation

o Scanning – ultrasonic testing techniques

o Testing parameters

o Examination

o Data presentation

Applications and acceptance criteria

o Scope

o Indication evaluation

o Acceptance criteria

o Test report

Reliability, quality of test results

o UT system performance

o NDT personnel competence

Certificate

On completion of the training program, the student will be awarded:

A Certificate of NDT – Ultrasonic Testing, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of NDT – Ultrasonic Testing is obtained after completion of the course and passing the online test.

Presentation

This training course provides a general introduction to ship machinery, details of diesel engines, a description of piping systems in ship's engine rooms and an overview of marine auxiliary machinery such as pumps, compressors, purifiers, heat exchangers, etc.

Objectives

On completion of the training, students will be able to:

Know the different types and arrangements of ship machinery applied for ship propulsion, understand the main parameters of ship machinery and the basic propulsion power transmission principles, and know the conceptual requirements for reliable and safe work of ship propulsion.

Know the main parts of marine diesel engines and understand their functions, get familiar with the most common problems involving engine parts, and understand the basic requirements for the reliable and safe operation of diesel engines.

Know the different types of piping systems in the ships engine room, understand the purpose and the basic arrangement of systems.

Know the different types of auxiliary machinery found on board ships, understand their working principles and the basic requirements for reliable and safe work of auxiliary machinery.

Program

Module 1 – Ship Machinery

Overview of the different propulsion types: Low-speed diesel engine layout, medium-speed diesel engine layout, steam propulsion with HP and LP steam turbines, gas turbines propulsion, diesel-electric propulsion, combined layouts, dual fuel engines, nuclear propulsion plants

Diesel engines outline

High pressure and low-pressure steam turbines 

Gas turbine cycles

Module 2 – Engine Details

Cylinder heads

Cylinder liners

Pistons

Crosshead and connecting rods

Bearings

Crankshaft

Engine casing

Turbocharger

Module 3 – Engine Room Systems

Seawater system

Freshwater system

Fuel oil system

Lubricating oil system

Compressed air system

Exhaust system

Module 4 – Marine Auxiliary Machinery

Pumps: Centrifugal pumps, positive displacement pumps, reciprocating pumps

Separators

Heat exchangers

Air compressors and air receivers

Steering gear

Reduction gears

Shaft generator

Thrust bearing

Controllable pitch propeller

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Marine Engineering Fundamentals, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Marine Engineering Fundamentals is obtained after completing the course and passing the online test.

Presentation

This training course provides a general introduction to welding, including an introduction to metallurgy, general information concerning welding, an overview of the electric arc processes commonly used in shipbuilding and details of welding inspection.

Objectives

On completion of the training, students will be able to:

Understand the nature and know the mechanical properties of metals; Understand the production process of steel and aluminium and the application of casting and forging processes.

Understand fundaments of fusion welding; Know how to determine heat input and preheat temperature; Understand the influence of the thermal cycle on weld microstructure and distortion; Know the general types of welding joints and the different welding positions

Know how to differ and recognize the arc welding processes used in shipbuilding; Understand the applicability and limitations of the different welding processes; Get familiar with common types of arc welding equipment and power sources

Know and apply the required activities in welding inspection; Determine and arrange the scope of inspection plan for different tasks; Know the different types of weld imperfections; Understand how to perform visual inspection of welding

Program

Module 1 – Introduction to Metallurgy

Module 2 – Welding Fundamentals

Module 3 – Arc Welding Processes

Module 4 - Welding Inspection

Certificate

On completion of the training program, the student will be awarded:

A Certificate of Welding Fundamentals, issued by Bureau Veritas Solutions Marine & Offshore.

The Certificate of Welding Fundamentals is obtained after completing the course and passing the online test.

Objective: The aim of the training is that theoretical and practical knowledge about fall protection and the correct use of rescue equipment, rescue of free-hanging persons, rescue of personnel over open sea, tank, stretcher transport, descent and treatment of personnel after fall accident is refreshed and repeated.

The training is adapted for personnel who are part of fall protection / rescue teams on board an installation. Participants must gain expertise in risk assessment, rescue (equipment and methods) and first aid.

Covers repetition requirements every 2nd year in accordance with NOG 113 and SFS.

Content:

Introduction
Regulations
Review of accidents and incidents
The rescue service
Equipment
Routines when working at height
Risk assessment
Management, site of injury
Stress and stress management
Hanging trauma, CPR
Rescue drills
Evaluation